Welcome
Please confirm your preferences
Update Preferences

Product Suggestions

Product Family suggestions

Contact a Kennametal Expert

Customer Support

Find customer support centers around the globe.

quick order warning
Enter a Material #, Customer Material #, or Catalog # (ANSI/ISO) to quickly add products to your cart.
Enter a Material #, Customer Material #, or Catalog # (ANSI/ISO) to quickly add products to your cart.
Enter a Material #, Customer Material #, or Catalog # (ANSI/ISO) to quickly add products to your cart.
Enter a Material #, Customer Material #, or Catalog # (ANSI/ISO) to quickly add products to your cart.
Enter a Material #, Customer Material #, or Catalog # (ANSI/ISO) to quickly add products to your cart.
Quick Order in Cart
Item(s) successfully added to the cart
View Cart
Item(s) are being added to the cart
View Cart
Turn up your volume for less with our limited-time offers! Shop Now

KM Indexable Torque and Power Calculator – Kennametal

For Indexable Insert End Mill with KM Quick-Change Tooling

These calculations are based upon theoretical values and are only intended for planning purposes. Actual results will vary. No responsibility from Kennametal is assumed.

Conversion of Workpiece Material Rockwell (Optional):
Metric
Inch

Conversion of Workpiece Material Rockwell (Optional)

Skip this step if you already know the Brinell hardness number(HB)
Characteristics of Workpiece Materials

Characteristics of Workpiece Materials

HB
PSI N/mm 2
Ultimate Strength shown for generic steel. Please enter the actual value of your workpiece material if available, for better accuracy You may look up this info through websites such as www.matweb.com
End Mill Nomenclature

End Mill Nomenclature

in.mm.
in. mm.
in. mm.

Machining Conditions

sfm m/min
in.(DOC) mm (DOC)
in.(WOC) mm(WOC)
in. IPT (chip load) mm
Most Common Workpiece MaterialsCm at W/D ratios:
W/D < = 0.660.66 < W/D < 1.0W/D = 1.0
Aluminum alloys1.01.051.1
Carbon and alloy steels1.01.151.3
Cast irons1.01.151.3
Titanium alloys1.01.201.4
Stainless steel, High-temperature alloys2.02.152.3
MillingDepth of cutFeed per toothCw
Category(min-max), in.(min-max), in.&nbsp;
Light0.020-0.1000.003-0.0061.1
Medium0.100-0.2000.006-0.0101.2
Heavy duty0.200-0.4000.010-0.0201.3
   
Direct Belt Drive.9
Back Gear Drive.75
Geared Head Drive.7-.8
Oil - Hydraulic Drive.6-.9

Safe Operating Conditions

lbN
lbN
ft lbNm
ft lbNm

Calculated Machining Conditions

RPM
(IPM)(no productivity formula)mm/min
in (chip load at the cut) mm/min
(IPM)(with productivity formula)mm/min
in.3/min MRRcm3/min3
in.2mm2

Calculated Required Power

lbf should not exceed Ft maxN
ft-lb should not exceed TpNm

Machining Power

HPckW
hpkW
Page Not Found
Welcome
Please confirm your preferences
Update Preferences

Product Suggestions

Product Family suggestions

Contact a Kennametal Expert

Customer Support

Find customer support centers around the globe.

quick order warning
Enter a Material #, Customer Material #, or Catalog # (ANSI/ISO) to quickly add products to your cart.
Enter a Material #, Customer Material #, or Catalog # (ANSI/ISO) to quickly add products to your cart.
Enter a Material #, Customer Material #, or Catalog # (ANSI/ISO) to quickly add products to your cart.
Enter a Material #, Customer Material #, or Catalog # (ANSI/ISO) to quickly add products to your cart.
Enter a Material #, Customer Material #, or Catalog # (ANSI/ISO) to quickly add products to your cart.
Quick Order in Cart
Item(s) successfully added to the cart
View Cart
Item(s) are being added to the cart
View Cart
Turn up your volume for less with our limited-time offers! Shop Now

Something went wrong.

We could not find that page. This page might have been removed or relocated.

Please consider using search to find the content you are looking for or go to our Homepage.

You are about to add to your My Solutions page. Do you want to proceed?
Select the destination where you want to move to.
New Folder
    • Applied Filters:
    • Clear All

A folder with the name already exists.

Special characters not allowed
Product successfully added to project __PROJECT_NAME__
product-image
Please adjust the following properties from

ISO Catalog Number

ANSI Catalog Number

to find similar products.

The following files are available

Please select a file to download

Models

I have read and accepted the Terms & Conditions of use

Can’t find the file type you’re looking for?

You should be logged to see your dashboard information
Session expired due to inactivity, please login again
The product/s () you were trying to add to the cart is/are not available, please contact customer service
item(s) successfully added to the cart
View Cart

. Please enter the desired qty for the material(s) you want to include in your promotion or Proceed Without Promotion and only your base materials will be added to the cart.

Minimum quantity should be

SAP Material Number ISO Catalog Number Grade    

You are about to leave the Solution building process.

Are you sure you want to leave?

Workpiece Selection

Standard

ALL

Material

Select a Value

Hardness

--

      Hardness Scale

      --

        Permitted Groups :

        Group

        SubGroup

        Hardness (HB)

        Hardness (HRC)

        Cancel Ok
        You are about to add to your My Solutions page. Do you want to proceed?
        Select the destination where you want to move to.
        New Folder
          • Applied Filters:
          • Clear All

        A folder with the name already exists.

        Special characters not allowed
        Product successfully added to project __PROJECT_NAME__
        product-image
        Please adjust the following properties from

        ISO Catalog Number

        ANSI Catalog Number

        to find similar products.

        The following files are available

        Please select a file to download

        Models

        I have read and accepted the Terms & Conditions of use

        Can’t find the file type you’re looking for?

        You should be logged to see your dashboard information
        Session expired due to inactivity, please login again
        The product/s () you were trying to add to the cart is/are not available, please contact customer service
        item(s) successfully added to the cart
        View Cart

        . Please enter the desired qty for the material(s) you want to include in your promotion or Proceed Without Promotion and only your base materials will be added to the cart.

        Minimum quantity should be

        SAP Material Number ISO Catalog Number Grade  

        You are about to leave the Solution building process.

        Are you sure you want to leave?

        Workpiece Selection

        Standard

        ALL

        Material

        Select a Value

        Hardness

        --

            Hardness Scale

            --

              Permitted Groups :

              Group

              SubGroup

              Hardness (HB)

              Hardness (HRC)

              CancelOk